This year for DragonCon I decided to tackle yet another Final Fantasy character (see Kefka and Yuffie from previous years.) Wanting to both stretch my crafting skills, as well as explore a character from another of my favourite games, I settled on Edea Kramer from Final Fantasy VIII.
Oh, no problem, just learn how to sew plunge necklines, make gradient fabrics, work with clay, beads, organza, magnets, and foam board. It was going to be a challenge, but that’s 90% of the fun for me, learning something new, and figuring out how to build something that both captures the character, and is wearable.
Part 1: Helmet
I’m going to spend the most time discussing the helmet, as it’s the most intricate piece of the costume, and it’s where I spent most of my effort. Primarily because I had no freaking idea how I was going to do this. I had never made anything even remotely similar to this before. Should I use a pre-formed helmet and add props, or make it from scratch? If starting from scratch, what materials do I use? Worbla, paper clay, bondo? These words were mostly giberish to me. I agonizing over this for about a month, I needed something that was fairly light, but that was also forgiving to work with, since I was a complete newb. Not having a mold of my head, I decided to start with paper mache to make my base, since I could apply it directly to my head. I maybe could have gone straight in with paper clay, but never having used it before, I was more comfortable starting with paper mache.
So here’s my smiling mug in about March of 2015. I started early to give myself lots of time to screw up. I covered my head with tinfoil and just started layering. Ryan helped me get the back of my head. Make sure to leave room for your hair if you plan to tuck it in. I didn’t make it too thick, maybe 4 layers. Just enough that it wouldn’t deform too much. Once completely dry I trimmed it to shape, including the peak at the front, notches for my ears, and a large notch at the back. Make sure you can move your head back and forth without it pinching your neck. Then I got a foam head from JoAnn’s to set this on to work with.
Next, horns. I swear I took pictures of this process, but unfortunately I messed up the reformatting of my phone back in the spring and lost a bunch of pictures that I hadn’t backed up. Now all my photos go directly into the cloud hivemind. Whether this is a better system or not, I’m not so sure…Also of note, don’t leave your horns, or any part of your costume for that matter, where you dog can get to them. I guess they looked like dog bones, and I had to re-make two of them.
To make the horns I started with tinfoil. I wanted a very light core, to minimize the weight pulling the helmet to one side or another. I crumpled it up and formed it into a very basic shape, then covered it with a few layers of paper mache. This worked out very well, as I could continue to shape and form the horns while I was layering on the paper. The final horns were stiff enough to hold shape, but not so stiff that I couldn’t do very small adjustments with some force. Then I glued the horns onto the cap. Do them one at a time, and make sure to mark your locations. You don’t want to have to pull them off and re-glue. Try the helmet on after each time to confirm the locations. Here’s the only picture I have of the helmet at this point. It’s not a good angle, sorry. Also in this photo you can see a very early dress prototype. Just testing out the plunginess of the neckline.
Once I was very VERY happy with the helmet (seriously, there’s not much opportunity to fix the shape after this point, make sure it’s perfect) I moved on to the clay. I had never worked with paper clay before, but I absolutely loved it! I used creative paper clay, which was about $12 a pound from Amazon, and I probably used two pounds total on the helmet. I also picked up some Gesso from Amazon for sealing.
On the first day I covered the whole helmet with the clay, including the horns. This was a bit of a mistake, as the weight of the clay on the horns caused them to sag. Remember how I said I had no idea what I was doing with this stuff? I wasn’t being modest :/ I spent a lot of time patching and reinforcing them. I worried I might have to scrap the whole thing, but my patience paid off. If doing it again I would clay only the cap and base the horns at first, and get them properly reinforced, then only proceed to clay the rest of the horns a few inches at a time once the base was dry. You can easily join pieces together with a bit of water, so no need to do it all at once.
The clay shrinks as it air dries though, so you will get cracking. Lots and lots and lots of cracking. I spent at least a week patching cracks, maybe two. I would come back to it every day and use a tiny trowel to shove more clay into little cracks, and smooth them over. Keeping it moist helps to smooth the surface, and the smoother it is now, the less sanding later, so keep water handy. Then it was another few weeks of sanding, patching little dimples with more clay, lather, rinse repeat. I probably could have kept smoothing for all of eternity, but at some point you have to say enough is enough.
I sealed the whole thing and then used painters tape to mark off some of the details. I started with the purple base, and then layered in some red wine colour on the horns. All of the paints were just basic acrylics from the craft store. I used some black and silver sharpies for a bit of detailing, as I’m really a terrible painter. I added a ridge of craft foam along the peak of the helmet and painted that gold.
With the helmet painted it was on to all of the little bits. Again, unfortunately a lot of these pictures were lost during the great phone reformatting of 2015. I started with the two big green wheels on either side of the helmet. I made the circles out of craft foam, then used paper clay to make the large ridges along the outside and the inner circle, and I used puffy paint to make the lines connecting the inner and outer circles. Seal and paint. Dry brush on a bit of black and grey to make it look a bit worn.
The gold spiral thingy on her left I used a similar technique to the horns to keep it light. I made a core out of aluminum foil and covered it in paper mache to get a basic shape, then used paper clay to make the final shape. This was an iterative process over a week or so layering on clay, smoothing it out, digging little channels, etc. Seal, paint, dry brush for a worn look.
The little claw/dagger thingy hanging on the left side is entirely paper clay. Make the base shape first then layer on a bit of detailing. Seal, paint, dry brush.
The spiky thing on the right hand side I made out of a few different materials. I started with large craft sticks (essentially large popsicle sticks) that I cut to shape, then I used paper clay to create the edging, and stuck a toothpick in the top of each one while it was still drying. Once dry I sanded it to the right shape, sealed, painted. The cross bars are extra thick craft foam.
I attached all these little bits and bobs with Quick Hold contact adhesive. HOW DID I NOT KNOW THIS EXISTED BEFORE!!! It’s by the makers of E6000, which is what you use in the craft world when you absolutely gotta get shit held together no matter what. But it takes a while for the bond to strengthen. Quick Hold is nearly as strong, but you get a perfect bond in just minutes. It’s amazing.
Here’s the final product. The final fit was quite good. I added a bit of padding into the helmet to make it sit a little higher on my head. I should have adding a bit more padding on the left side, as this was the heavier side, and it tended to tilt a little in that direction. Overall though it was not particularly heavy, and I comfortably wore it for half a day, two days in a row.
Part 2: Dress
I’m actually not going to say too much about the dress. I didn’t start it until about 2 weeks before DragonCon, at a time when I was rushing to finish other costumes as well. I’m overall not that happy with it, I was just too rushed to do a good job. It’s made out of a stretchy polyester material that does not breath at all. I cut a basic shape for the back and upper skirt and then drafted the pattern for the neckline myself and added some darts to make it fit around the bust. I didn’t really know how to make a plunge neckline and I don’t think I did a very good job, so I’ll likely re-do the dress at some point. I bought a few yards of pre-strung black feathers (i.e. the feathers are already attached in a line) and sewed them around the neck and shoulders in a few layers, with the inner layers covering up the edges of the outer layers. Then I used black bias tape to cover up the edge of the inner layer. For the lower skirt I made a basic flare skirt (alternating rectangles and triangles of fabric) out of a wine coloured polyester and used “Design Master” black spray paint to create the gradient. Design Master is a great brand of spray paint for fabrics, as it goes of extremely light. You can also use fabric paint, but I find the spray bottles they come in are terrible. I paired this with basic black stretchy gloves and some black heels, since I definitely do not have legs as long as any woman in any video game. I added claws to the gloves, but later took them off. I opted to lose a bit of the character for better functionality. The dress requires a plunge bra and lots of dress tape. Lots. Apologies in advance for the terrible bathroom selfie.
Part 3: Back Piece
The back piece was again something entirely new to me. I wasn’t too sure where to start. Wood? Cardboard? Plastic? Dowels? Vinyl? Foamboard? How will I attach it? How will I move while wearing it? How will I fit it in my tiny hatchback along with our 9 other costumes, a cooler, and other luggage to make it to DragonCon? I settled on foamboard for the entire thing, with a tiny bit of styrofoam added to make a wedge that held it out from my back a little bit (this was needed because I found the back horn from my helmet was hitting the backpiece, so I added the wedge to angle the back piece out away from me, giving me room to turn my head.)
The cool thing about the back piece, or at least the part that I think is cool, is that it’s made in three parts that attach with magnets. That’s right, magnets bitches!
The tedious part was cutting it out. My goodness did I have a massive callous on my middle finger from holding the knife! First I cut out all seven spikey pieces from foam board with an exacto knife, Something I learned after the first few spikes is that you need to change your blade constantly. After the blade starts getting dull it’s so much harder to cut, and your edges will come out really rough and chunky. To get a smooth edge I started changing the blade after each piece.
Here’s a pretty good in-progress photo showing all seven spikey pieces (there go my eloquent descriptions again), and the start of the connectors. Once the spikes were done I cut out a semi circle and sliced it into three segments and glued the long spiky pieces onto the segments in the final layout that I wanted. Then I made my six connecting pieces. Make sure to number your spikes and connectors segments so you know what order they go in, because they won’t all be perfectly identical. As you can see here I didn’t perfectly space my spikes, and the second segment from the right ends up being a bit short. Anyway, once the connectors were done I glued them to the spiky pieces, but NOT at the two gaps where the semi-circle segments come together. So, if you were to look at the pictures above and label the joints of spike to connector from left to right as 1 through 12, I left 4 and 9 unglued, leaving me with three completely separate pieces.
To join the three pieces I used tiny magnets embedded into the cross section of the foam board. This would allow me to disassemble the back piece into three separate pieces for transport, or to more easily move around the con floor. It also meant that if somebody knocked into my backpiece that instead of bending and potentially breaking it, the side piece would just snap back, and either fall off, or snap back into place, depending on how much it was displaced. This actually happened twice during DragonCon. Both times everyone around me gasped in horror, thinking my costume had just broken. However Ryan just picked the three pieces up and snapped them back on. It couldn’t have been easier.
I purchased neodymium magnets from K&J Magnetics Inc. I came across this company when purchasing neodymium magnets from some science outreach activities that I run. I’m glad I bookmarked the site, as their selection is amazing! The magnets I used were fairly small, so that they could fit into the cross section of the foam board. I used two sets of two at the top, in the connecting pieces, and two sets of two at the bottom in the semi-circle segments. I attached the magnets one one side first, then pressed the parts together and marked the connection point in the other side, before attaching the magnets in the other side, to make sure I aligned them correctly. I dug out a small hole into the foam and then dripped in a bit of glue, pressed the magnet in, and then covered it with some more glue. Be careful what kind of glue you use as a lot of it will eat through foam. I used a few different types through this process as an experiment. E6000 definitely eats through the foam. If you seal it with gesso first it’s not as bad, and is what I used on about half of these. School glue doesn’t eat through the foam, but isn’t as strong. Gorilla glue is strong AND doesn’t eat through the foam, but it expands quite a bit, and it’s hard to get the perfect amount. Overall I think school glue worked best.
Here are a few pictures of the magnets once inserted into the foam board (these pictures were obviously taken after painting, but I did the magnet insertion before painting.) The far left picture shows the magnets in one of the semi circle segments. The center pictures shows them in one of the connecting pieces. The right picture shows them in one of the spiky pieces. When you press the piece in the center to the piece in the right picture, those magnets will snap together. Remember, magnets have poles! When you’re putting in your magnets make sure you put them in facing the correct direction, otherwise your pieces will repel, not attract.
Now, those small magnets hold the three pieces together, but what holds the pieces to me? More magnets! I purchased some larger “sewing magnets”, again from K&J Magnetics. Sewing magnets come in pairs and are very strong, meant to be attached to each other through layers of fabric.
When they arrive they have a small plastic disk between each pair. I made the mistake of letting two magnets come together without anything in between them. I never got them apart again. I sewed the positive sides of these magnet sets into a bodice that I would wear under my dress. Just a quick safety note. Be very careful when working with these magnets. Keep them in a container at all times, especially if you have kids or pets. Swallowing one magnet isn’t that bad, as long as you pass it, but swallowing two can be deadly.
The little coloured dots in this photo are little dabs of paint. I did this so that I could then press the back piece up against the bodice and transfer the paint onto the backpiece, showing me where to put the magnet into the back piece. As I mentioned at the start of this section. I needed to make the back piece angle away from me, so that I didn’t hit it with my helmet. I did this by carving a wedge out of styrofoam (an electric turkey carving knife works great for this) and gluing the middle back piece to this wedge. I then attached all of the negative halves of the magnets into the styrofoam backpiece. Again, I tried different types of glue here, with varying levels of success. I was really worried about the magnets ripping out of the styrofoam, so I cut rectangles of craft foam and glued these over the magnets. This reduced the pull of the magnets a bit, so I used more magnets than I originally planned, but giving more surface area for the glue to bond to the styrofoam made it ultimately more secure. One or two of the magnets ended up coming loose, but nothing fell apart as the craft foam held it all in. I also attached a few more of the rectangle magnets into the face of the side pieces, and into the styrofoam wedge, so that the side pieces weren’t held to the main piece only by the magnets in the cross section. I didn’t take any pictures until I had already painted everything, so sorry but it’s hard to see some of the magnets. They look like little bumps/distortions in the bottom picture.
I painted everything using gold “Design Master” gold spray paint. Design Master is the only brand that I’ve found works with foam, everything else will tear it up unless it’s extremely well sealed.
Finally I made the flowing panels from a sheer white fabric and finished the upper edge with a white bias tape, so that I had a strong edge to glue to the foam board. I don’t have a serger and am terrible at sewing these fine fabrics. What I did was sew a zig zag stitch along all edges of the panels at a medium tension. No hem, just a zig zag along the raw edges. Keep the fabric taut, don’t let it bunch up or you won’t get a flat panel. Then trim all the edges as close as you can to the stitch, try to get all the stray fraying edges. Next light candle. Bring the edge of the fabric close to the flame, but not directly in it. This takes a bit of practice, so use some scraps first. The heat will burn up the raw edge to the thread, and make what looks like a nice rolled hem. You could probably also do this with a heat gun, but I don’t have one.
Here’s a few shots showing how the final assembly works.
First attach the center section to the back. Then attach the side sections one at a time. Magnets will snap the edges of the side sections to the edges of the center section at the top and bottom. Magnets on the front of the side sections will also snap to the styrofoam wedge at the bottom. You can see from the right photo how this allows the side sections to bend back slightly. It gives the appearance of a hinge, and will snap back into place if knocked slightly, or will fall off if knocked too far out of place.
Final attachment of the side sections. You can barely see the seams.
Finally, I put it all together and added some make-up! I know next to nothing about make-up, but I managed to get a decent look using a few simple items. Use a good foundation and powder to get a smooth complexion, since no women in video games have dry skin, oily skin, birth marks, acne, spotting, or any other physical imperfections. I used a basic black/neutral eyeshadow pallet, and a purple pallet to do the eyes. I didn’t use liner at all. The veins I used a white cream make-up (I had it left over from Kefka last year) to draw them with what was I think a lip liner brush? Then I used a small eyeshadow brush to add some shading with black and purple. I don’t really know enough about make-up to explain what I did, sorry. Just get a picture of Edea in front of you and start experimenting. Finish it off with some black mascara and purple lipstick.
Tom at Pixelated Images got a lovely close up of my make-up on Sunday night, though it was a bit smudged by this point.
Part 4: Seifer!
No Edea is complete without her knight, so I made a quick Seifer costume for Ryan. I purchased a used trench coat in his size and spent a few days modifying it, adding trim, cuffs, etc. I used bias tape to turn a blue t-shirt into the vest. The gunblade is what really makes the outfit through, and it was surprisingly simple. I cut the shape of the blade into two pieces of foam board, then attached them with contact cement. I shaped the blade edges and cut the small holes using a knife and sanded it. The gun part itself is made from a rubber/plastic gun that’s used in disarming exercises. I used a dremel to cut part of the end off, and a knife to trim the rubber back along the top of the barrel. I glue the blade on, and then used paper clay to shape the connection. By painting the part of the barrel where I trimmed the rubber back the same colour as the blade, it looks like the blade is coming from inside the gun.
Here’s Ryan rocking his costume, credit again to Pixelated Images for taking these great photos for us at con.
Part 5: Putting it all together
Not much more to say here. I really had an amazing time cosplaying as Edea at DragonCon. Ryan was a trooper about wearing that hot coat around, so thank you to him. He also acted as my sales man and kept showing people how my back piece came apart whenever they commented on it, as he was very impress by how I had engineered it. Thanks babe 🙂
The costume was fairly comfortable, though I did get a bit sweaty. I plan to remake the dress, and will make the feathering as a detachable overlay, so that I can wash the dress in the machine (I detest washing things by hand. I tend to put everything in the machine and if it gets destroyed, well, I didn’t want it anyway!) I also need to add a bit more padding to the helmet. Oh, one last item of note, I purchased and modified a running belt to go with this outfit, as I had no pockets. I made it a bit smaller so that it could go at my waist instead of my hips, and I added a buckle so that I didn’t have to pull it on over my legs. I also added a clip for my badge. This allowed me to carry around my phone, badge, and wallet without needing a bag, and it was easy to take off for photos, or just tuck my badge up under the belt.
Enough talk, here’s some photos of the Final Fantasy photo shoot that we went to on Saturday.
Standing around slightly awkwardly, as it started getting quite crowded at the shoot,and I was worried I was going to poke someone in the eye.
Nice group shots here with the other Final Fantasy VIII folks, and then one of the whole Final Fantasy group. These photos are courtesy Neko7 Cosplay Photography who came and took a ton of photos of our gathering. Check them out to find more great shots from the day (and the whole Con).
On Sunday evening Ryan and I decided to head down to the lower level of the Marriott and get a photo taken together by the con photographer. Unfortunately some butthole decided to steal the photographers camera, and we ended up waiting around for about 2 hours, which wasn’t really how I wanted to spend my last night. However, while waiting around, fully decked out, we ran in to lots of other cosplayers that were waiting around to get nice photos taken, and had some great conversations. We also ran into some wonderful photographers, and managed to get a few more nice photos taken, all while waiting around for our other nice photo! Tom at Pixelated Images, whom I mentioned earlier, was one of such photographers, as well as First Person Shooter from Nerd Caliber. Here are a few of the shots they took on Sunday night, as well as our photos from Bryan Humphrey: Mad Scientist with a Camera.
That’s it! I hope this write up is helpful to others interested in tackling these characters.
Update for DragonCon 2016
I wasn’t super happy with the coloring of the dress, and the back piece had fallen off a few times in 2015, so I decided to make some updates for 2016.
For the back piece, I kept the side magnets but replaced the back magnets and changed the wedge. I removed the styrofoam wedge entirely and made a new wedge from EVA foam. I attached black webbing straps directly to the wedge and did them up with parachute clips so that I could wear it on my back like a backpack and tighten as necessary. The feathers of the dress cover the straps so you don’t really see them. Then I attached large flush mount “Hillman” brand hangers to both the wedge, and to each of the three back pieces. This allowed me to hang the three back pieces from the wedge so they were secure, while still having a bit of flexibility from the magnets so that if I got hit from the side it would wobble instead of breaking. This worked so much better.
For the dress I dropped the idea of having a purple piece on the bottom and went all black. Then I used white and purple “design masters” brand spray paint to get the colouring that I wanted. I think it looks much better. I also made the feathers as a removable collar, attached with Velcro, so that I could easily wash the dress (it needed it…)
I bought Edea back to DragonCon 2017 but didn’t end up wearing her as I had too many other costumes. It may be time to retire Edea and start a new Final Fantasy build for 2018 🙂 Open to suggestions!